IMP(4) UNIX Programmer's Manual IMP(4) NAME imp - 1822 network interface SYNOPSIS /sys/conf/SYSTEM: NIMP _c_o_u_n_t # ARPAnet IMP 1822 interface DESCRIPTION The _i_m_p interface, as described in BBN Report 1822, provides access to an intelligent message processor normally used when participating in the Department of Defense ARPA net- work. The network interface communicates through a device controller, usually an ACC LH/DH or HDH or a DEC IMP-11A, with the IMP. The interface is "reliable" and "flow- controlled" by the host-IMP protocol. To configure IMP support, at least one of _a_c_c(4), _c_s_s(4) or _h_d_h(4) must be included. The _c_o_u_n_t specifies the total number of IMP connections. The network number on which the interface resides is specified at boot time using the SIOC- SIFADDR ioctl. The host number is discovered through receipt of NOOP messages from the IMP. The network interface is always in one of four states: up, down, initializing, or going down. When the system is booted, the interface is marked down. If the hardware con- troller is successfully probed, the interface enters the initializing state and transmits three NOOP messages to the IMP. It then waits for the IMP to respond with two or more NOOP messages in reply. When it receives these messages it enters the up state. The ``going down'' state is entered only when notified by the IMP of an impending shutdown. Packets may be sent through the interface only while it is in the up state. Outgoing packets are dropped with the error ENETDOWN returned to the caller if the interface is in any other state. DIAGNOSTICS imp%d: not configured. A hardware interface could not be attached during autoconfiguration because too few IMP pseudo-devices were configured. imp%d: leader error. The IMP reported an error in a leader (1822 message header). This causes the interface to be reset and any packets queued up for transmission to be purged. imp%d: going down in 30 seconds. imp%d: going down for hardware PM. imp%d: going down for reload software. imp%d: going down for emergency reset. The Network Control Center (NCC) is manipulating the IMP. By convention these Printed 11/26/99 August 2, 1987 1 IMP(4) UNIX Programmer's Manual IMP(4) messages are reported to all hosts on an IMP. imp?: host %x, lost %d rfnms. The IMP had messages out- standing to the host listed, but no RFNM (Request for Next Message) messages were received from the IMP in 127 seconds. The software state for that host is reinitialized. imp%d: interface reset. The host has received an interface reset message from the IMP. imp%d: address reset to x%x (%d/%d). The host has received a NOOP message which caused it to reset its notion of its current address. The Internet address is printed in hexade- cimal, with the host and IMP numbers following. This indi- cates that the address originally set by _i_f_c_o_n_f_i_g(8) was incorrect, that the IMP has undergone an identity crisis, or that communication between the IMP and the host is being garbled. imp%d: data error. The IMP noted an error in data transmit- ted. The host-IMP interface is reset and the host enters the init state (awaiting NOOP messages). imp%d: interface reset. The reset process has been com- pleted. imp%d: marked down. After receiving a "going down in 30 seconds" message, and waiting 30 seconds, the host has marked the IMP unavailable. Before packets may be sent to the IMP again, the IMP must notify the host, through a series of NOOP messages, that it is back up. imp%d: can't handle af%d. The interface was handed a mes- sage with addresses formatting in an unsuitable address fam- ily; the packet was dropped. SEE ALSO intro(4N), inet(4F), acc(4), css(4), hdh(4), implog(8), implogd(8) Printed 11/26/99 August 2, 1987 2