Internet Engineering Task Force I. Butcher/Pingtel
Internet Draft S. Lass/MCI
draft-sinnreich-sipdev-req-01.txt D. Petrie/Pingtel
July 2003 H. Sinnreich/MCI - editor
Expires: February 2004 C. Stredicke/snom
SIP Telephony Device Requirements, Configuration and Data
STATUS OF THIS MEMO
This document is an Internet-Draft and is in full conformance with
all provisions of Section 10 of RFC2026.
Internet-Drafts are working documents of the Internet Engineering
Task Force (IETF), its areas, and its working groups. Note that
other groups may also distribute working documents as Internet-
Drafts.
Internet-Drafts are draft documents valid for a maximum of six
months and may be updated, replaced, or obsoleted by other documents
at any time. It is inappropriate to use Internet-Drafts as reference
material or to cite them other than as "work in progress."
The list of current Internet-Drafts can be accessed at
http://www.ietf.org/ietf/1id-abstracts.txt
The list of Internet-Draft Shadow Directories can be accessed at
http://www.ietf.org/shadow.html.
Abstract
This informational I-D describes the requirements for SIP telephony
devices, based on the deployment experience of large numbers of SIP
phones and PC clients using different implementations. The document
reviews the generic requirements for SIP telephony devices, the
automatic device configuration process, device configuration data
and examples for XML configuration data formats.
SIP telephony devices are highly complex IP endpoints that speak
many Internet protocols, have text, audio and visual interfaces,
various input modes, and require functionality targeted at several
constituencies: (1) End users, (2) service providers and network
administrators and (3) manufacturers and system integrators.
The objectives of the requirements are a minimum set of
interoperability and multi-vendor supported core features, so as to
Page 1 6/17/2003
SIP Telephony Device Requirements July 2003
enable similar ease of purchase, installation and operation as found
for standard PCs, analog feature phones or mobile phones.
Conventions used in this document
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC-2119 [2].
The syntax and semantics used here extend those defined in SIP, [2].
Table of Contents
1. Introduction...................................................3
2. Generic Requirements...........................................4
2.1 Link Layer Requirements....................................4
2.2 IP Requirements............................................5
2.3 SIP Transport Requirements.................................5
2.4 SIP User Agent Services....................................6
2.5 Support for SIP Services..................................10
2.6 SIP and Other Related Protocols...........................11
2.7 SIP Security..............................................12
2.8 Voice Codecs..............................................12
2.9 Voice-Telephony Requirements..............................14
2.10 International Requirements...............................14
2.11 Support for Applications.................................15
2.12 Web-based Feature Management.............................15
2.13 Firmware Update..........................................16
2.14 Firewall/NAT Traversal...................................16
2.15 Device Interfaces........................................17
3. Automatic Configuration.......................................18
4. Configuration Settings........................................18
4.1 Device ID.................................................19
4.2 Network Related Settings..................................19
4.3 Address Completion........................................20
4.4 Audio.....................................................21
4.5 Local and Regional Parameters.............................22
4.6 Inbound authentication....................................23
4.7 Voice mail settings.......................................23
4.8 Phonebook and Call History................................24
4.9 Ringer Behavior...........................................24
4.10 User Related Settings and Roaming........................25
4.11 Line Related Settings....................................26
4.12 Line Identification......................................26
4.13 Registration period......................................26
H. Sinnreich Informational [Page 2]
SIP Telephony Device Requirements July 2003
4.14 Maximum connections......................................26
4.15 Call handling............................................27
4.16 Available Behavior.......................................27
4.17 Busy Behavior............................................28
4.18 Call Waiting Behavior....................................28
4.19 Do Not Disturb...........................................29
5. Examples of Configuration Data................................29
5.1. Requirements for Configuration Data Representation.......30
5.2 Configuration Data Format.................................30
5.3 Format Definition.........................................31
5.4 Handling of Unrecognized Element Names....................31
5.5 XML Configuration Data....................................31
5.6 Device settings...........................................31
5.7 User settings.............................................33
6. IANA Considerations...........................................34
7. Configuration Security........................................35
8. Acknowledgements..............................................35
9. Authors Addresses.............................................36
10. References...................................................37
11. Full Copyright Statement.....................................40
1. Introduction
This informational I-D has the objective of focusing the Internet
communications community on requirements for SIP [3] Telephony
devices.
We base this information on experience from developing and using a
large number of SIP telephony device types and on the experience
gained from large scale deployments in carrier and private IP
networks and on the Internet. This deployment has shown the need for
generic requirements for SIP telephony devices and also the need for
some specifics that can be used in SIP interoperability testing.
SIP telephony devices, also referred to as SIP User Agents (UAs) can
be any type of IP networked computing device enabled for SIP based
IP telephony. SIP telephony devices can be SIP phones, adaptors for
analog phones and fax machines, conference speakerphones, software
packages (soft clients) running on PCs, laptops, wireless connected
PDAs, as well as mobile and cordless phones that support SIP
signaling for real time communications.
SIP devices MAY also support various other media besides voice, such
as text, video, games and also possibly other Internet applications;
H. Sinnreich Informational [Page 3]
SIP Telephony Device Requirements July 2003
however the non-voice requirements are not specified in this
document, except when providing enhanced telephony features, as will
be shown.
The objectives of the requirements are a minimum set of
interoperability and multi-vendor supported core features, so as to
enable similar ease of purchase, installation and operation as found
for standard PCs, analog feature phones or mobile phones. Given the
cost of some screen phones or enterprise phones may approach the
cost of PCs and PDAs, and the larger number of phones compared to
PCs, similar or even better ease of use as compared to personal
computers and networked PDAs is expected by both end users and
network administrators.
As will be seen from the following, SIP telephony devices are highly
complex IP endpoints that speak many Internet protocols, have audio
and visual interfaces and require functionality targeted at several
constituencies: 1) End users, (2) service providers and network
administrators and (3), manufacturers, as well as system
integrators.
2. Generic Requirements
We present here a minimal set of requirements that MUST be met by
all SIP telephony devices, as specified here, except where SHOULD or
MAY is specified.
2.1 Link Layer Requirements
SIP devices MUST support either:
Link-1: Wired Ethernet IEEE 802.3 10Base-T 10 Mb/s Half Duplex, or
Link-2: Wireless Ethernet 802.11a/b/g
SIP devices MAY also support other link layer protocols, such as
Link-3: IEEE 802.3 10Base-T Full Duplex
Link-4: IEEE 802.3 100Base-T Half Duplex
Link-5: IEEE 802.3u 10/100Mb Auto-sensing
Link-6: SIP devices SHOULD support VLAN tagging as per IEEE 802.1q
H. Sinnreich Informational [Page 4]
SIP Telephony Device Requirements July 2003
Link layers used in 3rd generation mobile phone networks are out of
the scope for this document.
Power over Ethernet
Power-1: SIP telephony devices intended for desktop use MAY support
in-line power over Ethernet as specified in IEEE 802.3af.
Integrated Switch/Hub
SIP devices designed for wired Ethernet SHOULD have an uplink port
such that another IP device, such as a personal computer, MAY share
the network connection. SIP clients MUST prioritize the transmission
of the RTP traffic over the shared network connection.
2.2 IP Requirements
IP-1: SIP telephony devices MUST be able to acquire an IP address
by:
Automatic IP address configuration using DHCP, or
Manual IP address entry from the device.
IP-2: SIP devices MUST support multiple DNS entries. If the primary
DNS server does not respond to a DNS request, a secondary DNS server
MUST be queried.
IP-3: SIP devices MUST support IPv4 DSCP field for RTP streams that
supercedes the TOS bits described in RFC 791. The DSCP bit setting
MUST be possible to be configured by either the user or
automatically by the downloaded configuration data. The Assured
Forwarding DSCP value Low Drop Precedence for RTP voice packets MUST
be 100010 [4].
IP-5: SIP devices SHOULD support IP version 6.
2.3 SIP Transport Requirements
Transport-1: SIP clients MUST support UDP transport of SIP messages.
Transport-2: SIP clients MUST support TCP transport of SIP messages.
Transport-3: SIP devices MAY support RSVP (RFC 2205).
H. Sinnreich Informational [Page 5]
SIP Telephony Device Requirements July 2003
2.4 SIP User Agent Services
The requirements listed in this section may be used for device
testing. To verify correct functionality for specific services, the
support for the requirements in the next section should be tested.
The various call features listed here are also described in detail
in the SIP Service Examples [5].
SIP-1: SIP telephony devices MUST support RFC 3261 [2].
SIP-2, DNS SRV: SIP clients MUST support RFC 3263 [6] for locating a
SIP Server and select a transport protocol using NAPTR. When making
a SRV query, the client MUST use the additional information in the
response that contains the IP addresses for the A records.
If the DNS additional information is not present, the client MUST
make DNS A record queries to resolve the hostnames.
SIP-3, Do Not Disturb: Users MUST be able to set the state of the
device to Do Not Disturb (DND).
The change of the DND state SHOULD be communicated in a PUBLISH with
a tuple for this device to a configured presence server.
Re-invite: Clients MUST respond to new INVITES with a ô486 Busy
Hereö. Clients MUST respond to re-INVITES on existing dialogs as
normal behavior.
SIP-4, call hold resume: SIP clients MUST follow RFC 3264 [7] when
placing a call on hold. More specifically, the a=sendonly attribute
MUST be used. The SDP answer of SIP clients that are being placed on
hold MUST NOT contain "held" SDP, unless the user session was
originally on hold.
SIP-5, multiple calls: SIP clients that support call on hold MUST be
able to support at least two or more calls. By placing the current
call ôon holdö, the client MUST be able to initiate or receive
another call.
SIP-6, call waiting indicator: SIP clients MUST support a call
waiting indicator. When already participating in a call, the user
MUST be alerted audibly and/or visually of another incoming call.
The user MUST be able to enable/disable call waiting.
H. Sinnreich Informational [Page 6]
SIP Telephony Device Requirements July 2003
SIP-7, message waiting indicator: SIP clients MUST support SIP
message waiting [8] and the integration with voicemail platforms.
SIP-8, local dial plan: SIP clients MAY support a local dial plan.
The dial plan MUST consist of a pattern string to match dial digits,
and the ability to strip, append prefix digits, and/or append suffix
digits and send messages directly to another SIP device, bypassing
the proxy.
Note: Mobile SIP phones or PCs may not need a dial plan.
When using URL's and calling in the local domain, the local domain
(@domain) MAY be appended to facilitate calling.
If the destination SIP device is specified as an IP address, the SIP
client MUST not attempt to resolve the address with DNS as specified
in RFC 3263 [6].
If the destination SIP device is a string value, the SIP client MUST
make normal DNS SRV and A record queries as specified in RFC 3263.
SIP-9, transfer: SIP devices MUST support REFER and NOTIFY as
required to support the transfer [9]. SIP clients MUST support
escaped headers in the Refer-To: header.
SIP-10, unattended transfer: SIP devices MUST support an unattended
transfer. SIP clients MUST support escaped headers in the Refer-To:
header.
SIP-11, attended call transfer: SIP devices MUST support attended
call transfer. SIP clients MUST support escaped headers in the
Refer-To: header.
SIP-12, device based conferencing: SIP devices MAY be able to
support device based conferencing. A SIP client MAY be able to
initiate and mix the audio streams of at least 2 separate calls
(i.e. 3 way conference calling).
SIP-13, DMTF in-band mixing: SIP devices MUST generate in-band DTMF
tones for use with the G.711 codec.
SIP-14: DTMF RTP payload: SIP clients MUST be able to send DTMF
specified by RFC 2833 [10].
RFC 2833 negotiation must behave as follows: Receiving endpoint must
reply with payload type sent by initiator. For example, if the
H. Sinnreich Informational [Page 7]
SIP Telephony Device Requirements July 2003
initiating client sends payload type 101, receiving endpoint must
reply with payload type 101.
Payload type negotiation MUST comply with RFC 3264.
Payload type MUST remain constant throughout the session. For
example, if an endpoint decides to renegotiate codecs or put the
call on hold, the payload type for the re-invite MUST be the same as
initial payload type. SIP devices SHOULD support Flow Identification
(FID) as defined in RFC 3388 [11].
SIP-15, 180 ignores earlier media: SIP devices MUST generate local
ringing and MUST ignore any early RTP media when a ô180 Ringingö
response is received.
SIP-16, play single early media stream: SIP devices MUST play the
first RTP stream and ignore any other RTP media streams when a ô183
Session Progressö response is received.
SIP-17, use the last 18x message received: SIP devices MUST obey the
last 18x message received when multiple 18x responses are received.
If the last response is ô180 Ringingö; the client MUST generate
local ringing. If the last response is ô183 Session Progressö; the
client MUST play the RTP stream.
SIP-18, error-info support: SIP devices MUST support the Error-Info
header.
SIP-19, reason phrase display: If the ôReason Phraseö of a response
message is displayed, the client MUST use ôReason Phraseö in the
response packet.
The client MAY use an internal ôStatus Codeö table if there was a
problem with the language negotiation.
SIP-20, fax support: SIP adapter devices (for analog phone lines)
MUST support the ITU-T T.38 standard [12] using UDPTL [13]. SIP
devices MUST fallback to G.711 if T.38 fails.
Multi-line Requirements
SIP-21, multi-line support: Multi-line SIP devices MUST register
using more than one set of credentials.
H. Sinnreich Informational [Page 8]
SIP Telephony Device Requirements July 2003
SIP-22, multi-line Do Not Disturb: SIP multi-line devices MUST be
able to set the state of the client to Do Not Disturb on a per line
basis.
Clients MUST respond to new INVITES with a ô486 Busy Hereö. Clients
MUST respond to re-INVITES on existing dialogs as normal.
SIP-23, multi-line call waiting indicator: Multi-line SIP devices
MUST support multi-line call waiting indicators. When already
participating in a call, the user MUST be alerted audibly and/or
visually of another incoming call. This setting MUST be provisioned
by the user.
SIP devices with multiple identities (ie. registrations/lines) MUST
allow Call Waiting Indicator to be set on a per identity basis. If
call waiting is set for an identity, the client MUST respond with
ô486 Busy Hereö when an incoming call to that identity is received
and the client has an existing call with any of the identities.
SIP-24, Dynamic login/logout for user mobility: SIP devices SHOULD
support user mobility. SIP clients MAY store a static profile in
non-volatile memory so that this information is available during the
power up sequence. SIP clients MAY allow a user to walk up to a
client, login, and be able to send and receive calls with his/her
profile information.
For emergency numbers (e.g. 911, SOS URL) the client MUST send the
credentials username/password) of the static profile.
SIP-25, multi-line ring tones: SIP devices MUST be able to provision
a different ring tone for each line (i.e. registration or static
identity).
Analog text support for hearing or speech disabled users
SIP-26, analogue and digital text support for hearing and speech
impaired users: As per RFC 3351 [14], communicating with legacy
relay services and devices.
SIP adapter devices (for analog phone lines) supporting conversion
between real time text transmission using RFC 2793 [15] and analog
text telephones according to ITU-T V.18 MUST allow alternating use
of text and voice. SIP clients MUST fallback to G.711 if the RFC
2793 connection fails.
H. Sinnreich Informational [Page 9]
SIP Telephony Device Requirements July 2003
SIP devices must support TCP as specified in RFC 3261 for longer
text messages.
Digital text support: SIP telephone devices MAY support real time
text conversation using RFC 2793 for the text stream. It MUST be
possible to use text simultaneously with voice.
Note: Though SIP telephony devices supporting Instant Messaging
based on the SIMPLE [21] standard allow text conversation based on
blocks of text. However, interactive text conversation is required
for hearing and speech disabled users due to its streaming-like
nature.
SIP-27, call-info: SIP devices with a display MUST support the call-
info header and depending on the display capabilities MAY for
example display an icon or the image of the caller.
SIP-28, Priority header: SIP devices SHOULD support the Priority
header for such applications as emergency calls or for selective
call acceptance.
SIP-29: SIP devices MUST support music on hold as shown in "SIP
Service Examples" [5].
SIP-30: SIP devices SHOULD support the OPTION method as per RFC
3261.
2.5 Support for SIP Services
SIP devices used for enterprise communications SHOULD support the
call flows for the basic and enhanced SIP services. The list here
MAY be used for system integration testing to support specific
commercial services.
The schema for uploading the identity from a PDA is outside the
scope of these requirements.
The call flows illustrated in the references shown below assure not
only minimal support for SIP phones, as required for PSTN-style
consumer services, but also for the most widely used Centrex-style
and PBX-style services.
H. Sinnreich Informational [Page 10]
SIP Telephony Device Requirements July 2003
3rd party call control enables many value added services, such as
standards based control of a SIP phone from a call manager
application on the PC collocated on the desk with the SIP phone.
The following IETF references for rich presence, instant messaging,
caller preferences and service mobility specify SIP specific
services that go beyond the capability of PSTN and PBX based
services and can be best supported by SIP telephony devices.
Srv-1: SIP Call Flow Examples [16],
Srv-2: SIP Service Examples [17],
Srv-3: PSTN call flows [18],
Srv-4: Third Party Call Control in SIP [19],
Srv-5: SIP call control and multiparty features [20],
Srv-6: SIP devices MAY support conferencing services [21] for voice
and IM [22], so as to be able act as host for a 3-way conference at
least.
Srv-7: Rich Presence based services [23],
Srv-8: Caller and called party preferences [24],
Srv-9: Service mobility: SIP desk devices MAY allow roaming users to
upload their identity so as to have access to their services and
preferences from the home SIP server. Examples of user data to be
available for roaming users are: User service ID, the dialing plan,
personal directory and caller/called party preferences.
2.6 SIP and Other Related Protocols
SDP: SIP devices MUST support Session Description Protocol, RFC2327
[25].
RTP/RTCP: SIP devices MUST support Real-Time Protocol and Real-Time
Control Protocol, RFC 1889. SIP devices SHOULD use RTCP Extended
Reports for logging and reporting on network support for voice
quality [26].
H. Sinnreich Informational [Page 11]
SIP Telephony Device Requirements July 2003
SIP clients MUST support Simple Network Time Protocol (RFC2030), or
use the Date: header of the 200 OK in response to a REGISTER
request.
Network Management
SNMP: SIP clients SHOULD support SNMP reporting. SIP clients SHOULD
support the RTP and RTCP MIBs to report jitter, delay, and packet
loss.
2.7 SIP Security
Sec-1: SIP devices MUST support digest authentication as per RFC
3261.
Sec-2: SIP devices MUST be able to password protect configuration
information and administrative functions.
Sec-3: SIP devices MUST not display the password to the user or
administrator after it has been entered.
Sec-4: SIP clients MUST be able to disable remote access, i.e. block
incoming SNMP, HTTP, and other services not necessary for basic
operation.
Sec-5: SIP clients MUST be able to reject an incoming INVITE where
the user-portion of the SIP request URI is blank or does not match a
provisioned Contact. The setting to accept/reject MUST be
provisioned.
Sec-6: SIP clients MUST be able to reject an incoming INVITE when
the message does not come from the proxy or proxies where the client
is registered. For DNS SRV specified proxy addresses, the client
must accept an INVITE from all of the resolved proxy IP addresses.
2.8 Voice Codecs
Internet telephony devices face the problem of supporting multiple
codecs due to various historic reasons, on how telecom industry
players have approached codec implementations and the serious
intellectual property and licensing problems associated with most
codec types.
Many, but not all voice codec payload types are described in RFC
1890 [27].
H. Sinnreich Informational [Page 12]
SIP Telephony Device Requirements July 2003
Codec-1: Three main classes of voice codecs are supported by
Internet telephony devices; (1) default G.711, (2) compressed and
(3) wideband. At least two codecs, the default G.711 codec and one
compressed codec listed below MUST be supported.
1. SIP telephony devices MUST support AVT payload type 0 (G.711
uLaw] as the default codec. The packet size MUST be 20 milliseconds.
The matching ITU-T Appendix I and Appendix II decoders SHOULD also
be supported.
2. The compressed Internet Low Bit Rate codec (iLBC) [28], [29] MUST
be supported.
Other compressed codecs SHOULD be supported. Compressed Voice codecs
used in 2nd and 3rd generation mobile phone systems, such as various
GSM codecs are also found in various implementations and SHOULD be
supported.
The narrow bandwidth codecs such as G.723.1 with such low speed as
5.3 kb/s and 6.3 kb/s (without RTP/UDP/IP overhead) as to work well
even on dial-up access MAY be supported.
Compressed codecs such as G.729 derived from delta-PCM encoding,
found in networks with frugal Internet access bandwidth using frame
relay or DSL access MAY be supported.
3. Wideband codecs using typically 16 kHz voice sampling for better-
than-PSTN voice quality, such as G.722 and other MAY be supported.
Such codecs are found in conferencing systems to increase the
perceived quality of conferencing.
Note: A summary count reveals up to 25 and more voice codec types
currently in use. The authors believe there is a need for a single
multi-rate Internet codec, such as [30] that can effectively be
substituted for all the multiple codec types listed here and avoid
the complexity and cost implementers and service providers alike are
faced by supporting so many codec types, including especially those
that have not been developed specifically for Internet use.
Codec-2, codec negotiation: Endpoints MUST follow these guidelines
in RFC 3264: Initiator specifies "preferred" codec and the
receiver has "final" choice of codec selected.
Both endpoints MUST use the first codec listed by the receiver.
H. Sinnreich Informational [Page 13]
SIP Telephony Device Requirements July 2003
If an endpoint cannot dynamically switch between available codecs,
it MUST offer a single codec and send a new INVITE with another
codec if the original fails due to the SIP 488 "Media Unsupported"
message.
Codec-3, comfort noise: SIP devices MAY support comfort noise
generated in the receiver, without using up end-to-end bandwidth. It
is also RECOMMENDED that SIP clients comply with performance
specified for the "handset receive comfort noise" requirements
outlined in the ANSI/EIA/TIA-810-A-2000 standard.
2.9 Voice-Telephony Requirements
Voice-1, loudness: SIP telephony devices MUST conform to the
electro- acoustical requirements for send loudness rating (SLR),
receive loudness rating (RLR), weighted terminal coupling loss
(TCLw), stability loss, etc.) of the TIA/EIA standards [31], and
[32].
Stability loss is a measure of the contribution of the telephone set
or terminal to the overall connection stability requirements.
Stability loss is defined as the minimum loss from the terminal
digital input (receive) to the terminal digital output (transmit),
at any test frequency.
Voice-2, stability loss: SIP device SHOULD meet the following
stability loss requirements.
The stability or minimum loss, per ITU-T G.177, TIA/EIA-810-A and
TIA/EIA-579-A, at any voice-band frequency SHOULD be greater than 6
dB, and preferably greater than 10 dB. Digital telephone sets or
terminal equipment with adjustable receive level SHOULD maintain
stability over the entire range of adjustable receive levels.
Voice-3, speakerphone: SIP devices MAY provide a full-duplex
speakerphone with echo and side-tone cancellation.
Voice-4, programmable ring-tones: SIP device MAY be able to use
different ring-tones based on the caller identity (i.e. From:
header).
2.10 International Requirements
H. Sinnreich Informational [Page 14]
SIP Telephony Device Requirements July 2003
International-1, language support: SIP devices SHOULD indicate the
preferred language using SIP Caller Preferences. The setting for
this header MUST be provisioned.
International-2, international display support: SIP devices intended
to be used in various language settings, MUST support other
languages for menus, help, and labels.
2.11 Support for Applications
The following requirements apply to functions placed in the SIP
telephony device.
App-1, SIMPLE Integration: SIP devices that support presence MUST
provide a buddy list and use SIP extensions to leverage presence
[33].
App-2, address-book integration: SIP devices SHOULD allow a 3rd
party to initiate a call for the client, such as using the address
book in the PC to initiate a call.
App-3, LDAP phonebook: SIP devices MAY support LDAP for client-based
directory lookup.
App-4, automatic ring-down: SIP devices MAY support a phone setup
where a URL is automatically dialed when the client goes off-hook.
App-5, hold ring-back: SIP devices MAY ring after a call has been on
hold for a predetermined period of time, typically 3 minutes. This
time value MUST be provisioned.
2.12 Web-based Feature Management
Web-1: SIP devices SHOULD support an internal web server to allow
users to manually configure the phone and to set up personal phone
services such as the address book, speed-dial, ringer tones, and
last but not least the call handling options for the various lines,
aliases, in a user friendly fashion. Web pages to manage the SIP
telephony device MAY be supported by the individual device, or in
managed networks from centralized web servers. Managing SIP
telephony devices SHOULD NOT require special client software on the
PC or on a management console.
Web-2: The telephone settings MAY be accessible to authenticated
users or operations personnel from remote locations.
H. Sinnreich Informational [Page 15]
SIP Telephony Device Requirements July 2003
2.13 Firmware Update
Firm-1: SIP devices MUST be able to upgrade their firmware as
described in section 3.
2.14 Firewall/NAT Traversal
The following requirements allow SIP clients to properly function
behind various firewall architectures.
FW/NAT-1, outbound proxy support: SIP devices MUST support a default
domain used for NAT traversal. SIP devices MUST have the capability
to be configured so that the default domain and the outbound SIP
proxy are different.
The provisioned user identity on the device MUST include a full URL
to be included in the SIP From: header or a provisioned domain name
MUST be appended.
Configuration Information
Name: userA
Proxy Address: sip.outbound.domain.com
Domain: domain.com
Example Message sent to sip.outbound.domain.com
REGISTER sip:domain.com SIP/2.0
To: sip:userA@domain.com
From: sip:userA@domain.com
Contact: sip:10.10.10.215
FW/NAT-2, NAT capable configuration: SIP devices MUST be able to
operate behind a static NAT/PAT (Network Address Translation/Port
Address Translation) device using the STUN protocol [34]. SIP
clients MUST be able to populate SIP messages with the public,
external address of the NAT/PAT device and use specific port ranges
for RTP.
FW/NAT-3, UPnP capable configuration: SIP devices MAY be able to
operate with a UPnP (http://www.upnp.org/) firewall device. UPnP
will support the traversal of the local NAT/FW and is adequate on
its own when no other NATs are placed in the service provider
network.
H. Sinnreich Informational [Page 16]
SIP Telephony Device Requirements July 2003
FW/NAT-4, STUN capable configuration: SIP telephony devices MUST be
able to operate with a STUN server.
2.15 Device Interfaces
SIP telephony devices MAY have various types of interfaces, such as
resembling a desktop phone, cordless phone, mobile phone, handheld
computer, laptop computer and MAY have various interface models,
such as for phones, IM GUI or personal organizer. Given the variety
of possible interfaces, the generic requirements only can be listed
here.
Int-1: SIP telephony devices MUST have a telephony-like dial-pad and
MAY have telephony style buttons like mute, redial, transfer,
conference, hold, etc.
Int-2: SIP telephony devices MUST have a convenient way for entering
SIP URLs and phone numbers. This includes all alphanumeric
characters allowed in legal SIP URLs. Possible approaches include
using a web page, display and keyboard entry or graffiti for PDAs.
Phone number entry SHOULD be supported in human friendly fashion, by
allowing the usual separators and brackets between digits and digit
groups.
Int-3: SIP telephony devices MUST have two types of interface
capabilities, for both phone numbers and URLs, both accessible to
the end user.
1. SIP device configuration and management interface:
SIP telephony adapters and high end phones MAY support SNMP v.3 for
managing the device. The required MIB is outside the scope of this
memo.
The access to the SIP device configuration interface MAY be blocked
by the service provider so as not allow misconfiguration of the
settings.
2. End user options interface: Such as personal address book, auto-
forwarding, ringer tones, etc.
Desktop and other phone-style SIP devices can meet the above
requirements with a device web page. Device web pages may also
H. Sinnreich Informational [Page 17]
SIP Telephony Device Requirements July 2003
facilitate remote device settings from a help desk, without user
intervention.
3. Automatic Configuration
Automatic SIP telephony device configuration SHOULD use the
processes and requirements described in [35] and [36].
The user name or the realm in the domain name SHOULD be used by the
configuration server to automatically configure the device for
individual or group specific settings, without any settings by the
user.
Image and service data upgrades SHOULD also not require any settings
by the user.
4. Configuration Settings
Besides network parameters, SIP telephony devices MAY also be
configured with user data described here.
Settings are the information on a client that it needs to be a
functional SIP endpoint. It is an implementation choice whether the
device stores the data across power cycles and hardware restarts or
it reloads the data every time upon startup. The settings defined in
this document are not intended to be all inclusive. It MUST be
possible for vendor specific parameters to be added. Parameters
which are not understood by an end point MUST be ignored.
The list of available configuration settings includes settings that
MUST, SHOULD or MAY be used by all devices (when present) and that
make up the common denominator that is used and understood by all
devices. However, the list is open to vendor specific extensions
that support additional settings, which enable a rich and valuable
set of features.
Settings MAY be read-only on the device. This avoids the
misconfiguration of important settings by inexperienced users
generating service cost for operators. This draft describes how
operator MAY protect some settings from end users.
In order to achieve wide adoption of any configuration settings
format it is important that it not be excessive in size so as to
allow modest devices to use it. Any format SHOULD be structured
enough to allow flexible extensions to it by vendors.
H. Sinnreich Informational [Page 18]
SIP Telephony Device Requirements July 2003
Settings may belong to the device or to a line. When the endpoint
acts in the context of a line, it will first try to look up a
setting in the line context. If the setting can not be found in that
context, the device will try to find the setting in the device
context. If that also fails, the device MAY use a default value for
the setting.
The line concept allows configuration of phones in a user specific
context. It simplifies unconstrained seating in offices, can support
roaming users and allows users to subscribe to more than one service
provider.
In principle, all settings MAY be present in line and in device
context. For some settings (e.g. the MAC address of the device),
devices MAY set restrictions on the availability of settings in
either line or device context.
4.1 Device ID
A device setting MAY include some unique identifier for the device
it represents. This MAY be an arbitrary device name chosen by the
user, the MAC address, some manufacturer serial number or some other
unique piece of data.
4.2 Network Related Settings
Network-1: SIP Ports. The port that MUST be used for a specific
transport protocol MAY be indicated with the SIP ports setting. If
this setting is omitted, the device MAY choose any port.
Network-2: Quality of Service. The Quality of Service settings for
outbound packets SHOULD be configurable for network packets
associated with call signaling (SIP) and media transport (RTP/RTCP).
These settings help network operators identifying voice packets in
their network and allow them to transport them with the necessary
quality. The settings are independently configurable for the
different transport layers and signaling, media or administration.
For both categories of network traffic, the device SHOULD permit
configuration of the type of service settings for both layer 3 (IP
DiffServ) and layer 2 (IEEE 802.1D/Q) of the network protocol stack.
H. Sinnreich Informational [Page 19]
SIP Telephony Device Requirements July 2003
Network-3: Network parameters. The parameters for SIP (like timer
T1) and other network related settings MAY be indicated. An example
of usage would be the reduction of the DNS SRV failover time.
Network-4: RTP Port range. A range of port numbers MUST be used by a
device for the consecutive pairs of ports which MUST be used to
receive audio and control information (RTP and RCTP) for each
concurrent connection. This is required to support firewall
traversal. This again helps network operators to identify voice
packets and makes it possible to configure port ranges on firewalls
only for voice packets.
Network-5: Registration period. A line definition MAY contain a
period (in seconds) which once exceeded will cause the device to re-
register its registration server(s). The default value is one hour.
Network-6: Default Call Handling. All of the call handling settings
defined below in section 5.3.2 can be defined here as default
behaviors.
Network-7: Outbound Proxy. The outbound proxy for a line or for a
device MUST be set. The address is encoded as SIP URI. The setting
MAY contain alternative outbound proxies, which MAY be used in case
of a server failure.
Using this setting, private networks can control outbound traffic
and send it through an application layer gateway.
Network-8: Default Outbound Line. The default outbound line SHOULD
be a global setting (not related to a specific line). This setting
MUST not be used as part of a line definition.
Network-9: SIP Session Timer. The re-invite timer allows user agents
to detect broken sessions caused by network failures. A value
indicating the number of seconds for the next re-invite SHOULD be
used if provided. If there is no value provided, the device MAY use
a default value (e.g. 3600 seconds).
4.3 Address Completion
As most telephone users are used to dialing digits to indicate the
address of the destination, there is a need for specifying the rule
by which digits are transformed into a URL (usually SIP URL or TEL
URL).
H. Sinnreich Informational [Page 20]
SIP Telephony Device Requirements July 2003
Dial-1: SIP phones need to understand entries into the phone book of
the most common separators used between dialed digits, such as
spaces, angle and round brackets, dash and dots.
Dial-2: Dial Plan and/or Dial/OK key. A dial plan which defines the
maximum expected length of a typical telephone number MAY be used.
If no dial plan is used, the device MAY have a "Dial" or "OK" key,
similar to mobile phones.
Zero or more digit maps which map a dial plan and a SIP address to
which phone numbers of that type SHOULD be routed to SHOULD be
supported. The digit maps define numeric patterns that when matched
define:
1) A rule by which the end point can judge that the user has
completed dialing, and
2) A rule to construct a URL from the dialed digits, and optionally
3) An outbound proxy to be used in routing the SIP INVITE.
A critical timer MAY be provided which determines how long the
device SHOULD wait before dialing if a dial plan contains a T
character. It MAY also provide a timer for the maximum elapsed time
which SHOULD pass before dialing if the digits entered by the user
match no dial plan.
Dial-3: Default Digit Map. The end point SHOULD support the
configuration of a default digit map. If the end point does not
support digit maps, it SHOULD at least support a default digit map
rule to construct a URL from digits. If the end point does support
digit maps, this rule applies if none of the digit maps match.
Dial-4: Overlap-Dial. Some operators support overlap dialing and
MAY want to indicate to the SIP devices that this mode is to be
used. This setting is Boolean and MAY be set to true or false.
4.4 Audio
Audio-1: Codecs. In some cases operators want to control which
codecs MAY be used in their network. The desired subset of codecs
supported by the device MUST be configurable along with the order of
preference. Service providers MUST have the possibility of plugging
in their own codecs of choice.
H. Sinnreich Informational [Page 21]
SIP Telephony Device Requirements July 2003
The range for parameters of the codecs MUST be adjustable. This
includes the packet length (ms of audio), which is a function of
the sample rate.
However, the negotiation of the media for individual calls is being
done on a per call basis.
Audio-2: DTMF method. DTMF allows different ways of indicating that
a key has been pressed as per RFC 2833. The method for sending these
events SHOULD be configurable with the order of precedence.
Audio-3: Silence suppression. It SHOULD be possible to disable
silence suppression on the end point such that RTP audio packets are
sent even if silence is detected.
4.5 Local and Regional Parameters
Certain settings are dependent upon the devices regional location,
such as the daylight saving time rules and the time zone.
Regional-1: Time Zone. A time zone MAY be specified for the user.
Where one is specified; it SHOULD use the scheme used by the Olson
Time One database [37]. Examples of the database naming scheme are
Asia/Dubai or America/Los Angeles where the first part of the name
is the continent or ocean and the second part is normally the
largest city on that time-zone.
Regional-2: UTC Offset. An offset from Coordinated Universal Time
(UTC) in seconds MAY be used.
Different rules exist for when daylight saving time (DST) starts and
ends. For example in North America begins on the first Sunday in
April whereas in Western Europe is begins on the last Sunday in
March.
Regional-3: A DST rule MAY be used by the device.
The network addresses of SNTP (RFC 2030) time servers where the
device can get a centrally defined time value MAY be used.
Regional-4: The time server MAY be used. DHCP is the preferred way
to provide this setting. Setting the correct language is important
for simple installation around the globe.
H. Sinnreich Informational [Page 22]
SIP Telephony Device Requirements July 2003
Language-1: Language settings MAY be deployed. A language MAY be
specified for a device. Where it is specified it SHOULD use the
codes defined in RFC3066 [38] to provide some predictability.
Language-2: It is RECOMMENDED that servers set the Language as
writable, so that the user MAY change this. This setting SHOULD NOT
be line related.
Language-3: A SIP UA MUST be able to parse and accept requests
containing international characters encoded as UTF-8 even if it
canÆt display those characters in the user interface.
4.6 Inbound authentication
SIP allows a device to limit incoming signaling to those made by a
predefined set of authorized users from a list and/or with valid
passwords.
In-Auth-1: A device SHOULD support the setting as to whether
authentication (on the device) is required and what type of
authentication is REQUIRED: NONE or DIGEST.
In-Auth-2: If inbound authentication is enabled then a list of
allowed users and credentials to call this device MAY be used by the
device. The credentials MAY contain the same data as the credentials
for a line (i.e. URL, user, password digest and realm). This applies
to SIP control signaling as well as call initiation. The list shows
for example who is allowed to send a REFER or an INVITE with the
Join or Replaces header.
4.7 Voice mail settings
Various voice mail settings require the use of URL's as specified in
[39].
VM-1: The message waiting indicator (MWI) address setting controls
where the client MAY SUBSCRIBE to a voice mail server [40].
VM-2: A retrieve address MAY be used by the device so it can get any
voicemail messages it has.
VM-3: A deposit address MAY be used to specify where voicemail
messages SHOULD be left if the device is unable or unwilling to take
a call.
H. Sinnreich Informational [Page 23]
SIP Telephony Device Requirements July 2003
4.8 Phonebook and Call History
IP Telephony devices can store locally a phonebook and also the
history of recent calls. As an alternative, phonebook directory
servers can provide a centralized store of phone numbers/addresses
and potentially other information, such as provided by LDAP
directory servers.
Phonebook-1: SIP telephony devices MAY store telephone book entries
locally and/or MAY use a central LDAP directory.
A record of the last calls made and received MAY also be stored
locally or in a centralized location and referenced from devices.
Call Hisytory-1: SIP telephony devices MAY store locally a recent
(limited) call history or MAY make use of a central server for call
history. If the phone maintains only one last dialed number, it
SHOULD compare the incoming Last-Calls header against tried and
dialed and store the newest entry.
Devices that are not able to differentiate call history entries
between "tried" and "dialed" SHOULD use "dialed".
A server MAY be used for storing the phonebook and call history.
PhoneServers-1: Zero or more servers MAY be used for storing
phonebook directories or call histories. If a server is defined and
address such as a URL MUST be used and user name and credentials MAY
be used for that server.
The flush timeout MAY be specified for the server.
Users MAY wish to limit the number of data items that are returned
to their device if a query is issued against one of the directory
servers.
4.9 Ringer Behavior
The manner in which a user is alerted to an incoming call (visually,
audibly or possibly both) MAY be used by the device. This includes
the different volumes and MAY point to a file that contains the
melody for the ringer alert.
Ringer sound files MAY be specified for the following types of
incoming calls normal, high priority, internal and external.
H. Sinnreich Informational [Page 24]
SIP Telephony Device Requirements July 2003
Different ringer sound files MAY also be associated with different
lines.
The location of a call MAY also be indicated. This allows using the
phone by hearing-impaired or in noisy environments where external
speakers are used to render the sound. The location of the call is
also useful for paging by speakerphones.
4.10 User Related Settings and Roaming
A device MAY specify the user which is currently registered on the
device. This SHOULD be an address-of-record URL specified in a line
definition.
The purpose of specifying which user is currently assigned to this
device is to provide the device with the identity of the user whose
settings are defined in the user section. This is primarily
interesting with regards to user roaming. Devices MAY allow users to
sign-on to them and then request that their particular settings be
retrieved. Likewise a user MAY stop using a device and want to
disable their lines while not present. For the device to understand
what to do it MUST have some way of identifying users and knowing
which user is currently using it. By separating the user and device
properties it becomes clear what the user wishes to enable or to
disable.
Providing an identifier in the configuration for the user gives an
explicit handle for the user. For this to work the device MUST have
some way of identifying users and knowing which user is currently
assigned to it.
One possible scenario for roaming is an agent who has definitions
for several lines (e.g. one or more personal lines and one for each
executive for whom the administrator takes calls) that they are
registered for. If the agent goes to the copy room they would sign-
on to a device in that room and their user settings including their
lines would roam with them. The alternative to this is to require
the agent to individually configure all of the lines individually
(this would be particularly irksome using standard telephone button
entry).
The management of user profiles, aggregation of user or device lines
and profile information from multiple management sources are
configuration server concerns which are out of the scope of this
document. However the ability to uniquely identify the device and
H. Sinnreich Informational [Page 25]
SIP Telephony Device Requirements July 2003
user within the configuration data enables easier server based as
well as local (i.e. on the device) configuration management of the
configuration data.
UserID-1: User ID MAY be specified. If the user ID is specified,
the address-of-record URL MAY be specified for the line definition.
4.11 Line Related Settings
SIP telephony devices MUST use the line related settings, as
specified here.
4.12 Line Identification
A line represents an address-of-record identified by a URL.
There are many properties which MAY be associated with or SHOULD be
applied to the line or signaling addressed to or from the line.
Lines MAY be defined for a device or a user of the device. At
least one line MUST be defined in the configuration settings, this
MAY pertain to either the device itself or the user.
A line MUST provide a address or record URL which both distinguishes
the line and provides the URL which optionally will be registered
for the line. A user friendly display name SHOULD be taken from the
address-or-record URL for the line.
A line definition MUST specify whether the line SHOULD automatically
register with a registration server. It MUST be possible to specify
at least one set of realm, user name and authentication credentials
for each line. The user name and authentication credentials are used
upon authentication challenges.
A line definition MUST use call handling settings and the state of
the phone to determine how to handle inbound calls. Inbound calls
MAY be rejected, redirected, or accepted.
4.13 Registration period
A line definition MAY contain a period (in seconds) which once
exceeded will cause the device to re-register its registration
server(s). The default time is one hour.
4.14 Maximum connections
H. Sinnreich Informational [Page 26]
SIP Telephony Device Requirements July 2003
A setting defining the maximum number of simultaneous connections
that a device can support MUST be used by the device. Obviously the
end point has some maximum limit, most likely determined by the
media handling capability. The number of simultaneous connections
may be also limited by the access bandwidth, such as of DSL, cable
and wireless users.
MaxConn-1: A SIP telephony device MAY support at least two
connections for three-way conference calls that are locally hosted.
4.15 Call handling
Call Handling settings define how the phone reacts to a new incoming
call given different situations. In some cases, an end user MAY want
to redirect calls to another party, rejected the call, or accept the
call and alert the end user. Some settings tend to change
irregularly like their voicemail forwarding address while other
settings such as the Do Not Disturb state MAY change often. Private
networks and service provider networks MAY enable very sophisticated
call handling options that MAY be supported more effectively on SIP
servers, rather than in all SIP telephony devices. In such networks,
call handling options in the SIP telephony device MUST be disabled
to avoid feature interaction.
CallOptions-1: Local call handling options like forwarding, such as
to voice mail or other locations, available and busy behavior MUST
have the option of being disabled locally, in case these services
are provided by a SIP server.
4.16 Available Behavior
The Available Behavior defines how a new call is handled when the
phone is not actively engaged in a call or when Call Waiting is
enabled. Options include RING and FORWARD_ON_NO_ANSWER. A setting of
RING alerts the user (as defined by the Ringer Behavior in 3.2.3)
for a practical length of time before returning an error response
to the caller if not answered.
Available-1: All end points MUST use an available behavior setting.
Available-2: FORWARD_ON_NO_ANSWER SHOULD alert the user for a
configured amount of time (Forward on No Answer Timeout) and if not
answered, forward to the Forward on No Answer address.
H. Sinnreich Informational [Page 27]
SIP Telephony Device Requirements July 2003
The Forward on No Answer setting identifies the address forwarded
"To:" after an alerting call exceeds the Forward On No Answer
Timeout period. End points MUST use this parameter if the
available behavior is set to FORWARD ON NO ANSWER and MAY define
this parameter otherwise.
The Forward on No Answer Timeout defines the length of time that a
user SHOULD be alerted for before the call is automatically redirect
to the Forward on no answer SIP URL. This parameter is specified in
seconds, where approximately 4 seconds is equivalent to a ring. End
points MUST use this parameter if the available behavior is set to
FORWARD ON NO ANSWER and MAY define this parameter otherwise.
4.17 Busy Behavior
The Busy Behavior defines how a new call is handled when the phone
is engaged in an active call and call waiting is disabled or when
the phone has reached the maximum number of connections. Options
include BUSY and FORWARD. A BUSY setting instructs the phone to
respond with a 486/Busy here. A FORWARD setting redirects the caller
to the Forward on Busy Address.
Busy-1: All SIP devices MUST use a busy behavior setting.
The Forward on Busy SIP URL setting identifies the address forwarded
to when the end point is busy. The end point is considered busy if a
call is active and call waiting is disabled and when the phone has
reached the maximum number of simultaneous connections. Since this
parameter is dependent on the busy behavior, end points MUST define
this setting if the BUSY behavior is set to FORWARD and MAY define
this setting otherwise.
4.18 Call Waiting Behavior
Call Waiting controls the behavior of new calls when an existing
call is already active and the device has not met the maximum
number of connections. Options include ALERT and BUSY, where ALERT
will alert the user as defined by the Ringing behavior and
Available Behavior and BUSY will follow the busy behavior logic.
All end points MUST use a call waiting behavior setting.
Fwd-1, Unconditional Forwarding: The Unconditional Forwarding
setting allows end users or administrators to forward all inbound
calls to a designated Unconditional Forwarding SIP URL. This is
useful if one wants to temporarily redirect all calls to another
H. Sinnreich Informational [Page 28]
SIP Telephony Device Requirements July 2003
end point and administrative access to the directory servers is
unavailable.
Options include ENABLE and DISABLE, where ENABLE indicates that all
inbound calls will be redirected and DISABLE indicates that all
inbound calls will be treated as specified by the available, busy,
and call waiting behaviors. All end points MUST support
unconditional forwarding.
The Unconditional Forwarding SIP URL identifies the address that
inbound calls are redirected to if Unconditional Forwarding is
enabled. All end points MUST use the unconditional forwarding
address if unconditional forwarding is enabled, otherwise they MAY
use it.
4.19 Do Not Disturb
The Do Not Disturb setting enables end users to quickly and easily
enable and disable inbound calls for a particular line. Options
include ENABLE and DISABLE, where ENABLE will handle a call as
indicated by the Do Not Disturb Method and DISABLE allows normal
call handling. This setting MUST be used by all end points.
This setting MAY seem redundant to other parameters defined within
call handling, however, it addresses both an end user needs along
with administrative requirements. In some configurations, an end
point MAY be configured to return a BUSY response to an inbound call
so that a user agent within the network can try another party.
The same results are required for Do Not Disturb.
DND-1: Do Not Disturb Method MUST be able to support multiple
methods of rejecting calls. Options include BUSY, FORWARD_ON_BUSY,
and FORWARD_ON_NO_ANSWER. A setting of BUSY will return a BUSY
response so that other network user agents can redirect the call
as needed.
FORWARD_ON_BUSY will redirect the call to the FORWARD_ON_BUSY SIP
URL and FORWARD_ON_NO_ANSWER will for privacy reasons allow the
caller to believe the call is alerting before forwarding to the
Forward on No Answer SIP URL.
5. Examples of Configuration Data
The section describes the requirements and format for an
implementation of the settings described in section 4.
H. Sinnreich Informational [Page 29]
SIP Telephony Device Requirements July 2003
5.1. Requirements for Configuration Data Representation
From reading the preceding section 4, it is apparent that many of
the settings are composite and related. As the number and complexity
of the settings grows it is useful from an administration point of
view to be able to easily relate settings.
This document recognizes that as features multiply on devices, so
will the amount of settings. Any format proposed SHOULD be readily
and intuitively extensible.
5.2 Configuration Data Format
The choices for the configuration data formats are best left to the
discretion of the implementers and service providers.
Open Issue: The authors believe it would be useful to specify a
grammar for the default name space.
This document illustrates however using XML as the file format for
the configuration settings primarily for the reasons stated above.
XML naturally maps the settings defined in section 4.
Note for potential grammar designers and implementers: The authors
believe it is very useful to have CDATA sections in XML documents
where the content itself may break XML syntax rules. This is the
case of SIP URLs. An example of is given in Example E below.
XML namespaces are a useful tool when processing documents which MAY
contain elements from more than one source. The default namespace
for any XML document using the definitions described in this
document MUST define the default namespace in the root node with a
URL.
Vendors MAY add their own content within the XML document but MUST
provide qualified names with their own namespace.
The general format for the XML data is to have device and user
elements as direct children of the root node. Those elements will
contain all of the appropriate settings describe in section 3.
An example of an extension to the time zone setting is show below.
H. Sinnreich Informational [Page 30]
SIP Telephony Device Requirements July 2003
00:d0:1e:00:1a:0eNORTH AMERICAAmerica/Los_Angeles"PST"10.1.1.1US:English
5.3 Format Definition
The definitions of the elements and attributes will not be included
in this version of the draft, given that only examples are shown
here. The examples follow to only illustrate some concepts of the
format. Section 4 defines the requirements from which the XML
elements and attributes will be derived. The authors believe the
data format definitions and grammar for SIP telephony device
configuration data SHOULD be the object of separate documents.
5.4 Handling of Unrecognized Element Names
The default rule is that any element with an unrecognized name is
ignored (i.e. having an unrecognized namespace URI, or an
unrecognized local name within that namespace). This includes all of
the element content, even if it appears to use recognized names.
5.5 XML Configuration Data
This section aims to provide some samples of the settings defined in
section 4, using XML [41]. A complete grammar/schema definition is
not provided here, since this serves as an example only.
5.6 Device settings
A. Network Settings
5060
H. Sinnreich Informational [Page 31]
SIP Telephony Device Requirements July 2003
506010030010.1.1.110.1.1.180
B. Address Completion
91XXXXXXXXsip:{digits}@provider1proxy.provider1:port011X*sip:internation
C. Audio
D. Line default settings
10.1.1.1
H. Sinnreich Informational [Page 32]
SIP Telephony Device Requirements July 2003
E. Line definition for device
Pingtel.comanonpassword232sip:admin@acme.com
In this example the outbound proxy and call handling settings
defined in the line default settings example SHOULD be used in
addition to the line definition.
Note: The authors' preference for potentially long values in XML is
to use an element rather than an attribute. Added to which, in an
element you can wrap values which would normally break the XML
syntax in a CDATA. This would allow SIP URLs to be formatted
without having to escape them.
Example:
<[!CDATA[ôExtension 123ö]]
5.7 User settings
F. Voice mail settings
10.1.1.110.1.1.2
H. Sinnreich Informational [Page 33]
SIP Telephony Device Requirements July 2003
G. Line definition for user
<Fred Bloggs>sip:fbloggs@Pingtel.comPingtel.comfredbabdc342RRe
provider1.comfredbloggsbdc42jjRe
Credentials are supplied for two realms in this example. In this
example the outbound proxy and call handling settings defined in the
line default settings example SHOULD be used in addition to the line
definition.
6. IANA Considerations
SIP Event Package Registration for Configuration
Package name: SIP Telephony Device Configuration
Type: package
Contact: [Christian Stredicke]
Published Specification: This document.
MIME Registration for Application
The MIME Registration for application/sip-endpoint-configuration is:
MIME media type name: application
H. Sinnreich Informational [Page 34]
SIP Telephony Device Requirements July 2003
MIME subtype name: sip-endpoint-configuration
Required parameters: none.
Optional parameters: none.
Encoding considerations: See SIP [3] message header definition.
Security considerations: See the "Security Considerations" in
Section 8 n this document.
Interoperability considerations: none
Published specification: This document.
Applications which use this media: SIP configuration server and
clients subscribing to these servers.
Additional information:
1. Magic number(s): N/A
2. File extension(s): N/A
3. Macintosh file type code: N/A.
7. Configuration Security
Please see also the above section 2.7 on SIP Security.
The device configuration MAY contain sensitive information that MUST
be protected. Examples include authentication information, private
address books and call history entries. Because of this, it is
RECOMMENDED to use an encrypted transport mechanism for
configuration data. Where devices use HTTP this could be TLS [42].
For devices which use FTP or TFTP for content delivery this can be
achieved using symmetric key encryption.
Access to retrieving configuration information is also an important
issue. A configuration server SHOULD challenge a subscriber before
sending configuration information.
8. Acknowledgements
The authors would like to thank numerous persons for contributions
and comments to this Internet Draft: Henning Schulzrinne from
H. Sinnreich Informational [Page 35]
SIP Telephony Device Requirements July 2003
Columbia University, J÷rgen Bj÷rkner from HotSIP, Jay Batson from
PingTel, Eric Tremblay from Mediatrix, Gunnar Hellstr÷m from Omnitor
AB, David Oran and Denise Caballero McCann from Cisco, Brian Rosen
from Marconi, Jean Brierre from MCI, Kai Miao from Intel, Adrian
Lewis from Profile-ICT and Franz Edler from UTA Telekom AG. Jonathan
Knight from MCI has contributed significantly to earlier versions of
parts of this Internet Draft. Peter Baker from Polycom has also
provided valuable pointers to TIA/EIA IS 811 requirements to IP
phones that are referenced here.
9. Authors Addresses
Ian Butcher
Pingtel Corp.
400 W. Cummings Park
Suite 2200
Woburn, MA 01801, USA
Phone: +1 781 938 5306
Email: ibutcher@pingtel.com
Steven Lass
MCI
400 International Parkway
Richardson, TX 75081, USA
EMail: steven.lass@mci.com
Phone: +1 972 729 4469
Daniel G. Petrie
Pingtel Corp.
400 W. Cummings Park
Suite 2200
Woburn, MA 01801, USA
Phone: +1 781 938 5306
Email: dpetrie@pingtel.com
Henry Sinnreich
MCI
400 International Parkway
Richardson, TX 75081, USA
EMail: henry.sinnreich@mci.com
Christian Stredicke
snom technology AG
Pascalstrasse 10e
10587 Berlin, Germany
H. Sinnreich Informational [Page 36]
SIP Telephony Device Requirements July 2003
Phone: +49(30)39833-0
Email: cs@snom.de
10. References
[1] RFC2026: "The Internet Standards Process -- Revision 3" by Scott
Bradner, IETF, October 1996.
[2] RFC 2119: "Key words for use in RFCs to Indicate Requirement
Levels" by Scott Bradner, IETF, 1997.
[3] J. Rosenberg et. al.: "SIP: Session Initiation Protocol, RFC
3261, IETF, June 2002.
[4] RFC 2597: "Assured Forwarding PHB Group" by Heinanen, J. et al.
IETF, June 1999.
[5] Johnston, A. et al., "SIP Service Examples", work in progress,
February 2003.
[6] RFC 3263: "Session Initiation Protocol (SIP): Locating SIP
Servers" by J. Rosenberg and H. Schulzrinne. IETF, June 2002.
[7] RFC 3264: "An Offer/Answer Model with Session Description
Protocol (SDP)" by J. Rosenberg and H. Schulzrinne. IETF, June 2002.
[8] Mahy, R.: "A Message Summary and Message Waiting Indication
Event Package for SIP". Work in progress, IETF March 2003.
[9] RFC 3515: "The SIP Refer Method" by R. Sparks, IETF, April 2003.
[10] RFC 2833: "RTP Payload for DTMF Digits, Telephony Tones and
Telephony Signals" by H. Schulzrinne and S. Petrack. IETF, May 2000.
[11] RFC 3388: "Grouping of Media Lines in the Session Description
Protocol (SDP)" by G. Camarillo et al. IETF, December 2002.
[12] ITU-T Recommendation T.38.
[13] Johnston, A. et al.: "Session Initiation Protocol Torture Test
Messages". Work in progress, August, 2002.
[14] RFC 3351: "Requirements for the Session Initiation Protocol
(SIP) in Support of Deaf, Hard of Hearing and Speech-impaired
Individuals" by Charlton, N. et al. IETF, August 2002.
H. Sinnreich Informational [Page 37]
SIP Telephony Device Requirements July 2003
[15] RFC 2793: "RTP Payload for Text Conversation" by G. Hellstrom.
IETF, May 2000.
[16] Johnston, A. et al.: "Session Initiation Protocol Basic Call
Flow Examples". Work in progress, IETF, August 2003.
[17] Johnston, A. et al.: "Session Initiation Protocol Service
Examples", work in progress, IETF, February 2003.
[18] Johnston, A. and Donovan S: "Session Initiation Protocol PSTN
Call Flows". Work in progress, IETF, November 2003.
[19] Rosenberg, J., et al., " Best Current Practices for Third Party
Call Control in the Session Initiation Protocol", work in progress,
March 2003
[20] Mahy, R.et al., "A Call Control and Multi-party usage framework
for the Session Initiation Protocol (SIP)", work in progress, IETF,
March 2003.
[21] Johnston A. and Levin O.: "Session Initiation Protocol Call
Control - Conferencing for User Agents", work in progress, IETF,
April 2003.
[22] Rosenberg, J. and Isomaki, A.: "Requirements for Manipulation
of Data Elements in Session Initiation Protocol (SIP) for Instant
Messaging and Presence Leveraging Extensions (SIMPLE) Systems ",
work in progress, IETF, August 2003.
[23] Rosenberg, J., et al., "Rich Presence Information Data Format
for Presence Based on the Session Initiation Protocol (SIP) ", work
in progress, IETF, August 2003.
[24] Rosenberg, J. et al.: "Caller Preferences and Callee
Capabilities for the Session Initiation Protocol (SIP) ", work in
progress, IETF, September 2003.
[25] RFC 2327: "SDP: Session Description Protocol" by M. Handley and
V. Jacobson. IETF, April 1998.
[26] T. Friedman et al: "RTP Control Protocol Extended Reports (RTCP
XR)", work in progress, IETF, April 2003.
[27] H. Schulzrinne et al.: "RTP Profile for Audio and Video
H. Sinnreich Informational [Page 38]
SIP Telephony Device Requirements July 2003
Conferences with Minimal Control", RFC 1890, IETF, January 1996.
[28] Andersen,S.V. et al.: "Internet Low Bit Rate Codec", work in
progress, IETF March 2003.
[29] Duric A. et al.: "RTP Payload Format for iLBC Speech", work in
progress. IETF March 2003.
[30] Herlein, G: "RTP Payload Format for the Speex Codec", work in
progress, IETF, February 2003.
[31] TIA/EIA-810-A, "Transmission Requirements for Narrowband Voice
over IP and Voice over PCM Digital Wireline Telephones", July 2000.
[32] TIA-EIA-IS-811, "Terminal Equipment - Performance and
Interoperability Requirements for Voice-over-IP (VoIP) Feature
Telephones", July 2000.
[33] Rosenberg, J.: "A Presence Event Package for the Session
Initiation Protocol (SIP)", work in progress, IETF, January 2003.
[34] Rosenberg, J. et al: "STUN - Simple Traversal of User Datagram
Protocol (UDP) Through Network Address Translators (NATs)". IETF,
March 2003.
[35] Petrie, D.: "A Framework for SIP User Agent Configuration",
work in progress. IETF, February 2003.
[36] Petrie, D. and Jennings, C.: "Requirements for SIP User Agent
Profile Delivery Framework", work in progress, IETF, February 2003.
[37] Eggert, P.: "Sources for time zone and daylight saving time
data." Available at http://www.twinsun.com/tz/tz-link.htm
[38] Alvestrand, H.: "Tags for the Identification of Languages", RFC
3066, IETF, January 2001.
[39] Mahy, R. et al.: "A Multi-party Application Framework for SIP",
Internet Draft, IETF, June 2002, work in progress.
[40] Mahy, R.: "A Message Summary and Message Waiting Indication
Event Package for SIP", work in progress, IETF, march 2003.
[41] T. Bray, J. Paoli, C. Sperberg-McQueen and E. Maler,
"Extensible Markup Language (XML) 1.0 (Second Edition)", W3C
H. Sinnreich Informational [Page 39]
SIP Telephony Device Requirements July 2003
Recommendation, October 2000, http://www.w3.org/TR/2000/REC-xml-
20001006.
[42] RFC 2818: "HTTP over TLS" by E. Rescorla. IETF, May 2000.
11. Full Copyright Statement
Copyright (c) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph
are included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
H. Sinnreich Informational [Page 40]